反解法在再入机动弹道设计中的应用研究

简要分析了一般的再入机动弹道设计方法,即正解法.针对正解法对模型依赖性强和对初值非常敏感的问题,提出了一种基于误差补偿的机动弹道设计方法——反解法.该方法从弹道终端出发反解弹道,将计算结果误差转化为机动点参数误差,再通过关机点或中制导的调整进行误差补偿,从而有利于命中精度和打击效果的实现.仿真结果表明,该方法计算简便,对工程应用有一定的参考价值.     

5GHz雷达的干扰计算模型概述

文章从开发5 GHz模型的目的入手,简要介绍了5 GHz模型的结构组成,详细讨论了5 GHz模型的干扰计算流程,包括无线局域网和雷达的场景设置、技术参数设置、总干扰计算等,最后给出了5 GHz模型的一个运行范例,以期为其它干扰模型的开发提供借鉴参考。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

GPS弹道修正引信弹道环境信息的解算与数值仿真分析

根据质点弹道的特点, 描述了弹目间距、弹炮间距和相对弹道高 3个弹道环境信息的概念, 然后应用数学方法对弹目间距、弹炮间距和相对弹道高进行了理论计算推导, 建立了数学解算模型, 并用MATLAB程序进行了数值仿真计算, 通过分析其数值变化的规律和特点提出了其应用方向。     

航空发动机在超声速引射系统中的应用分析

航空发动机可以对空气增压,并且增加气流温度,理论上存在应用于超声速引射系统的可能。分析了气源对引射器性能的影响以及引气对航空发动机的影响,介绍了3种航空发动机在超声速引射系统中可能的布局方案。针对某领域内的排气参数要求,分别对3种布局方案进行了计算分析。计算结果表明,当上游气体压强为0.044×10⁵ Pa和0.029 3×10⁵ Pa时,通过合理选择发动机的布局以及工作参数,发动机可以直接将上游气体排出或者作为驱动气源应用于超声速引射系统。     

平行双线式电火工品感应电流仿真研究

根据Agrawal理论,建立平行双线式电火工品的传输线模型,通过仿真计算分析外界电磁场和电火工品各物理参数对负载端感应电流大小的影响,为电火工品的射频安全性研究提供一定的参考．     

非线性隔冲系统最大响应的计算方法

提出了一种计算具有三次方非线性刚度的单自由度隔冲系统最大响应的方法 ,该方法将计算过程分成冲击作用阶段和自由衰减振动阶段 .在冲击作用阶段中 ,认为系统的冲击刚度为常数 ;在自由衰减振动阶段中 ,考虑系统的刚度非线性 ,用迭代法推导出了系统最大位移和最大加速度的一阶近似表达式 .据此可用数值计算的方法求出系统的最大位移和最大加速度     

一种计算涡轮增压柴油机高原性能的方法

提出了一种计算涡轮增压柴油机高原性能的方法.这种方法不涉及复杂的数值模拟计算,可以在较宽广的环境压力和环境温度范围预测涡轮增压柴油机的性能,具有较高的计算精度.对两台车用涡轮增压柴油机进行了实例计算,并与试验结果进行了对比.分析了海拔高度变化和温度变化引起的涡轮增压器和发动机性能的变化趋势.     

几何光学法用于飞机进气道 RCS 的计算

运用电磁场理论的几何光学法解决飞机进气道雷达截面(RCS)的计算。计算结果与实测值基本相符,使得复杂的飞机进气道雷达特性可以简化处理。此法既简单又严密。     

DSP实现坦克火控系统弹道微分方程数值算法

针对现役坦克火控系统弹道解算广泛采用的逼近法的缺点和不足,提出了改进后的弹道微分方程直接数值解算算法,以数字信号处理器(DSP)作为该算法的硬件实现环境进行了实验。结果表明,以DSP技术为基础的改进弹道微分方程解算算法解决了逼近法的不足。解算速度快,精度高。这说明该算法在坦克火控系统应用中具有良好的发展前景。